tap and die size for the swing arm pivot bolt and the frame

Post Reply
justdave
Posts: 9
Joined: Sun May 06, 2007 8:30 pm

tap and die size for the swing arm pivot bolt and the frame

#1

Post by justdave »

Hello all, anybody know the tap and die size for the swing arm pivot bolt and the frame where it fits into on a '58 FL. Thanks. DaveZ



Bigincher
Posts: 2789
Joined: Tue Dec 18, 2007 2:10 pm
Bikes: 1941/59 EL
1952 FL
1977 FLH
1994 Fatboy
Has thanked: 21 times
Been thanked: 103 times

Re: tap size

#2

Post by Bigincher »

Hello Dave. Looks like 5/16"x18tpi. Check this page out of the parts catalog. Sorry about it being sideways, had to do that to fit the upload parameters here. You can copy it and rotate it back. Hope this helps.
You do not have the required permissions to view the files attached to this post.

hplhd
Posts: 643
Joined: Sat Apr 30, 2005 7:16 pm
Bikes: 1998 heritage springer
1959 FLH
Location: indiana, usa
Has thanked: 18 times
Been thanked: 28 times

Re: tap size

#3

Post by hplhd »

dam tom i had to turn my monitor on its side.
Last edited by hplhd on Sun Aug 23, 2009 4:58 pm, edited 2 times in total.

panhead
Site Admin
Posts: 2799
Joined: Wed Dec 12, 2001 9:17 pm
Bikes: 1954 FL
Location: Holland
Has thanked: 29 times
Been thanked: 169 times

Re: tap size

#4

Post by panhead »

1958 Frame.jpg
You do not have the required permissions to view the files attached to this post.

Bigincher
Posts: 2789
Joined: Tue Dec 18, 2007 2:10 pm
Bikes: 1941/59 EL
1952 FL
1977 FLH
1994 Fatboy
Has thanked: 21 times
Been thanked: 103 times

Re: tap size

#5

Post by Bigincher »

hplhd wrote:dam tom i had to turn my monitor on its side. this is rich(nuklhd) by the way.
Hey Rich, fancy meeting you here!

RUBONE
Moderator
Posts: 6133
Joined: Sat Nov 15, 2008 4:09 am
Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
Has thanked: 117 times
Been thanked: 1144 times

Re: tap size

#6

Post by RUBONE »

The thread is 5/8 x 18. It is a standard configuration available everywhere.
Robbie

FlatHeadSix
Moderator
Posts: 2681
Joined: Sun Jun 06, 2004 5:14 pm
Bikes: '31 VL, '34 VD, '45 WLA, '47 WL, '49 FL, '51 WL, '58 ST (Hummer), '71 GE (Servi)
Location: Lonoke, Arkansas
Has thanked: 5 times
Been thanked: 37 times

Re: tap size

#7

Post by FlatHeadSix »

Robbie is correct, the parts book is wrong (at least that version is). It shows that item #14, the nut that fits on the pivot bolt, is a 5/16 x 18 with a 15/16 hex. Whoa, that would have to be one tough 5/16 bolt to handle that!

I think I would go with the 5/8, it wouldn't be the first time they made a mistake in the parts book.

mike

panhead_kicker
Posts: 978
Joined: Fri Oct 03, 2008 2:57 am
Bikes: Pan
FLHP Evo
E-H Super X
Chubble head hack
Servi-car
Topper(s)
Model 64D (Hey its got 3 wheels!)
Location: Indianapolis
Has thanked: 106 times
Been thanked: 79 times

Re: tap size

#8

Post by panhead_kicker »

the nut that fits on the pivot bolt
Am I silly or what? What's that nut for? A longer pivot bolt and a stripped out frame?

Panacea
Posts: 1922
Joined: Fri May 24, 2002 1:00 am
Bikes: 64FL 99FLHR 01FXSTD
Location: Mpls. MN.
Has thanked: 17 times
Been thanked: 83 times

Re: tap size

#9

Post by Panacea »

V-Twin makes a special pivot bolt for stripped out frames. It's on page591 in the catalog...Mike

Bigincher
Posts: 2789
Joined: Tue Dec 18, 2007 2:10 pm
Bikes: 1941/59 EL
1952 FL
1977 FLH
1994 Fatboy
Has thanked: 21 times
Been thanked: 103 times

Re: tap size

#10

Post by Bigincher »

FlatHeadSix wrote:Robbie is correct, the parts book is wrong (at least that version is). It shows that item #14, the nut that fits on the pivot bolt, is a 5/16 x 18 with a 15/16 hex. Whoa, that would have to be one tough 5/16 bolt to handle that!
I think I would go with the 5/8, it wouldn't be the first time they made a mistake in the parts book.
mike
I agree, sure looks like a typo to me...!

Cotten
Posts: 6913
Joined: Mon Aug 26, 2002 9:09 am
Location: Central Illinois
Has thanked: 100 times
Been thanked: 281 times

Re: tap size

#11

Post by Cotten »

All the Panheads I have known screwed into the frame, not a nut.
And a helicoil fixes a stripped frame quite well.

It appears to be a string of typos, as even my '65 book lists the phantom "5/16-18" nut.
That's a lot of years to leave a misprint!

Other places where the 7980 nut is used lists the correct 5/8-18.

Perhaps some of the confusion arose from the fact that the pivot bolt itself is fabricated with a nut welded upon it.

...Cotten

panhead_kicker
Posts: 978
Joined: Fri Oct 03, 2008 2:57 am
Bikes: Pan
FLHP Evo
E-H Super X
Chubble head hack
Servi-car
Topper(s)
Model 64D (Hey its got 3 wheels!)
Location: Indianapolis
Has thanked: 106 times
Been thanked: 79 times

Re: tap size

#12

Post by panhead_kicker »

It appears to be a string of typos, as even my '65 book lists the phantom "5/16-18" nut.
That's a lot of years to leave a misprint!
You still stand by that star hub diagram Cotten? <grin>
Sorry, I had to do it! I was trying to figure out what the nut was for myself.

Cotten
Posts: 6913
Joined: Mon Aug 26, 2002 9:09 am
Location: Central Illinois
Has thanked: 100 times
Been thanked: 281 times

Re: tap size

#13

Post by Cotten »

panhead_kicker wrote: You still stand by that star hub diagram Cotten? <grin>
Sorry, I had to do it! I was trying to figure out what the nut was for myself.
Certainly.

At least the hub has alternative diagrams, such as the Armored School Handbook, to verify it.
Have we any alternative swingarm diagrams?

By the way, does anyone know off-hand the difference between '58-'62 47500-58 swingarms and '63-'72 47500-63 units?

...Cotten

Bosheff
Posts: 1262
Joined: Fri Jul 03, 2009 8:23 pm
Bikes: 65 FLH 82 FLH
Location: Michigan
Been thanked: 58 times

Re: tap size

#14

Post by Bosheff »

It seems to me that some sort of gusseting or strengthing was done to the swing arm.

indianut
Posts: 161
Joined: Fri Aug 08, 2008 1:26 pm
Bikes: American
Location: Florida
Been thanked: 8 times

Re: tap size

#15

Post by indianut »

Cotten wrote:
By the way, does anyone know off-hand the difference between '58-'62 47500-58 swingarms and '63-'72 47500-63 units?

...Cotten
I believe it is the Grease Fitting?

Post Reply

Return to “Frame & Fittings”